How Many Rolls of Loft Insulation Do I Need? Quick Chart, Worked Example and Calculator
To work out how many rolls of loft insulation you need, measure the loft floor area in m², add about 10% for cutting, then divide by the coverage of one roll (it's printed on each roll and shown on our product pages) for each layer, and round up. For the recommended 270–300mm you'll usually lay two layers: one between the joists and one across them. For example, a 40m² loft needs 5 rolls of 100mm and 7 rolls of 200mm ODE Lunaflex for 300mm, or 4 rolls of 100mm and 6 rolls of 170mm Knauf Loft Roll 44 for 270mm. The chart below gives quick numbers for common loft sizes, and the rest of this guide covers coverage per roll, a worked example and when PIR board is the better choice.
How many rolls of loft insulation do I need? Quick chart
| Loft floor area | ODE Lunaflex, 300mm total | Knauf Loft Roll 44, 270mm total |
|---|---|---|
| 20m² | 3 × 100mm + 4 × 200mm | 2 × 100mm + 3 × 170mm |
| 30m² | 4 × 100mm + 5 × 200mm | 3 × 100mm + 5 × 170mm |
| 40m² | 5 × 100mm + 7 × 200mm | 4 × 100mm + 6 × 170mm |
| 50m² | 6 × 100mm + 9 × 200mm | 4 × 100mm + 7 × 170mm |
| 60m² | 7 × 100mm + 10 × 200mm | 5 × 100mm + 9 × 170mm |
Rolls per layer, including 10% for cutting and waste, using the coverage printed on each roll. One layer goes between the joists and one across them. Check your own measurements, or use the loft roll calculator for an exact, priced list.
Need a quick quantity or thickness check? Use our free loft roll calculator. It uses the products we sell, prices the list live, and you can add it to your basket. Results are estimates — call 03330 908479 if you want us to check your sizes.
How deep should loft insulation be?
Building Regulations set U-values rather than depths. In England, Approved Document L gives 0.16 W/m²K for an upgraded roof and 0.15 W/m²K for a new roof on an extension, and Wales has its own Approved Document L. For mineral wool laid at ceiling level in a cold loft, around 270mm is the commonly recommended depth, and going deeper improves performance further.
The usual approach is two layers:
- First layer between the joists, the same depth as the joists (often 100mm in older houses).
- Second layer across the joists at right angles, which covers the timbers and cuts heat loss through them. A 200mm top layer over 100mm between the joists gives 300mm in total.
How many rolls do I need?
- Measure the loft floor area (length × width) in m².
- Add around 10% for cutting and waste.
- For each layer, divide by the coverage of one roll and round up.
Coverage per roll for the loft rolls we stock:
| Product | Thickness | Coverage per roll |
|---|---|---|
| ODE Lunaflex Loft Roll Ultra 42 | 100mm | 10.83m² |
| ODE Lunaflex Loft Roll Ultra 42 | 150mm | 7.98m² |
| ODE Lunaflex Loft Roll Ultra 42 | 200mm | 6.84m² |
| URSA 10 DIVERSO | 150mm | 8.55m² |
| URSA 10 DIVERSO | 200mm | 6.27m² |
| Knauf Loft Roll 44 Combi-Cut | 100mm | 13.89m² |
| Knauf Loft Roll 44 Combi-Cut | 150mm | 9.18m² |
| Knauf Loft Roll 44 Combi-Cut | 170mm | 8.01m² |
| Knauf Loft Roll 44 Combi-Cut | 200mm | 6.84m² |
Worked example: a 40m² loft
A loft measuring 8m × 5m with 100mm-deep joists, insulated to 300mm with ODE Lunaflex:
- Area with 10% waste: 40 × 1.1 = 44m²
- Between the joists, 100mm: 44 ÷ 10.83 = 4.1, so 5 rolls
- Across the joists, 200mm: 44 ÷ 6.84 = 6.4, so 7 rolls
At the time of writing (11 November 2026), ODE Lunaflex 100mm is £27.87 and ODE Lunaflex 200mm is £32.81 ex VAT per roll, so the rolls for this example come to £365.38 ex VAT. Our minimum order is £400 ex VAT, so you'd need to add a little more, such as a spare roll or other materials for the job. If you already have some insulation between the joists and it is dry and in good condition, you may only need the top layer.
Tips for a better job
- Don't squash it. Compressed mineral wool performs worse. If you want to board the loft for storage, use raised loft legs so the boards sit above the full depth of insulation.
- Keep the eaves clear. Leave a ventilation gap at the eaves so air can flow into the roof space, and use eaves vents or trays if needed.
- Mind the cables. Where possible, lift electrical cables so they sit on top of the insulation rather than buried in it, and follow the manufacturer's guidance for any recessed lights. Ask an electrician if you are unsure.
- Leave a gap under the cold water tank so a little warmth reaches it from below, and insulate the tank and any pipework in the loft instead.
- Insulate and draughtproof the hatch. An uninsulated hatch is a big cold spot.
- Wear gloves, a mask and long sleeves when handling mineral wool, and open compressed rolls in the loft, as they expand quickly.
Loft roll or PIR board?
For a cold loft insulated at ceiling level, loft roll is usually the right choice. It is quick to lay over large areas, fills the gaps between joists well and is cost-effective. Glass mineral wool such as URSA 10 DIVERSO is also rated Euroclass A1 (non-combustible).
PIR board earns its place where space is tight, because it gives much more insulation per millimetre. Compare two manufacturers' datasheet figures: 200mm URSA 10 DIVERSO has a thermal resistance of 4.50 m²K/W, and so does 100mm Recticel Eurothane GP PIR board. PIR does the same job in half the thickness, which is why it is chosen for:
- Room-in-the-roof and loft conversions, between and under the rafters
- Walls and floors, where every millimetre counts
- Insulating at rafter level to keep the loft space warm
Rafter-level insulation needs more thought about ventilation and condensation. Our free PIR U-value calculator has a pitched roof option, and our wool vs PIR vs foil guide compares the materials in more detail. For step-by-step fitting, see our guide to installing loft insulation.
Order your loft insulation
Order ODE Lunaflex 100mm for between the joists and 200mm for across them, see every roll in our loft insulation range, or read 270mm loft insulation: what thickness do I need? Prices are shown ex VAT. Loft roll is delivered in England only, free, with a £400 ex VAT minimum order (see delivery information). Call us on 03330 908479 (Mon–Thu 8am–5pm, Fri 8am–12pm), email sales@insulationwarehousedirect.co.uk, or order online.
Guide only: figures are typical values for general information. Always check the manufacturer's current data sheets and confirm Building Regulations compliance with your designer, SAP assessor or building control. Insulation Warehouse Direct accepts no liability for decisions made using this guide.
Sources: Approved Document L, Volume 1 (GOV.UK), Tables 4.2 and 4.3; URSA 10 DIVERSO datasheet; Recticel Eurothane GP datasheet. Coverage figures are from our product listings. Correct at the time of writing.
