WhatsApp us
Stack of green-faced moisture resistant tapered edge plasterboard sheets

Moisture Resistant vs Vapour Plasterboard: Which for Kitchens and Bathrooms?

Kitchens, bathrooms and utility rooms put plasterboard under more stress than any other room in the house. Steam from showers and cooking, splashes around sinks and condensation on cold walls all take their toll on standard board. The two boards most often suggested for these rooms are moisture resistant board and vapour board. They do different jobs, and in some rooms you need neither. This guide explains the difference and where each one belongs.

Quick answer

  • Moisture resistant board copes better with humidity and occasional splashing. Use it for walls and ceilings in kitchens, bathrooms, utility rooms and en-suites.
  • Vapour board has a metallised backing that limits water vapour passing through the board into the wall or ceiling behind. Use it on the warm side of external walls, sloping ceilings and ceilings under cold lofts, where vapour could condense inside the structure.
  • Neither is waterproof. Areas that get wet directly, such as inside a shower enclosure, need a cement-based or specialist wet-area board, or a tanking system, as specified by the board and tile manufacturers.

Moisture resistant plasterboard

Moisture resistant (MR) board has water-repellent additives in the gypsum core and a treated paper liner, which help it resist the effects of humid air and splashes. It usually has a green face, which makes it easy to tell apart from standard board on site.

Typical uses:

  • Bathroom and en-suite walls and ceilings outside the shower zone
  • Kitchen walls, particularly behind sinks and worktops
  • Utility rooms and toilets
  • A base for tiles in splash areas, within the board manufacturer's tile weight limits

It is fixed, jointed and finished in the same way as standard board. At the time of writing, our 12.5mm moisture resistant tapered edge board is £12.61 ex VAT per 2400 × 1200mm sheet, and a 15mm version is also available.

Vapour plasterboard

Vapour board is standard plasterboard with a metallised film on the back. The film acts as a vapour control layer, reducing the amount of moist indoor air that can pass through the board and condense on colder surfaces behind it, such as the inside of an external wall, the timber in a sloping ceiling or the underside of a cold loft.

  • Fix it with the metallised side facing the framing or cavity and the ivory face into the room.
  • It needs to be mechanically fixed to studs, battens, joists or metal framing. British Gypsum states that its equivalent board is not suitable for fixing with adhesive, so do not dot-and-dab vapour board.
  • The film only works if it is continuous. Keep cuts neat and seal around pipes, cables and downlights.

At the time of writing, our 12.5mm vapour tapered edge board is £13.46 ex VAT per sheet.

Many insulated plasterboards and foil-faced PIR boards already include a vapour control layer, so check the manufacturer's guidance before adding another one.

Which board for which room?

Location Typical choice
Bedrooms, living rooms, hallways Standard board
Kitchen and utility walls Moisture resistant board
Bathroom walls outside the shower zone Moisture resistant board
Bathroom ceiling under a cold loft Moisture resistant board, with vapour control and careful sealing around fittings
Inside a shower enclosure or wet room Cement-based or wet-area board, or tanking
Warm side of an insulated external wall or sloping ceiling Vapour board, unless the insulation already provides a vapour control layer

Condensation risk depends on the whole construction. For anything beyond a like-for-like replacement, ask your designer or the insulation manufacturer for a condensation risk assessment.

Don't forget ventilation

The right board helps, but getting rid of the moisture matters most. Approved Document F (England) sets minimum intermittent extract rates of 15 litres per second for a bathroom, 30 l/s for a utility room, and 30 l/s for a kitchen with a cooker hood extracting to the outside (60 l/s without one). Our guide to controlling damp and moisture covers ventilation and condensation in more detail.

Frequently asked questions

Is green plasterboard waterproof?

No. Moisture resistant board resists humidity and occasional splashes, but it is not designed for areas that are regularly soaked.

Can I use moisture resistant board on a bathroom ceiling?

Yes, it is a common choice. If there is a cold loft above, limiting the moisture that gets into the loft matters too, so seal around downlights and the hatch and make sure the extractor is doing its job.

Order your plasterboard

Browse our full plasterboard range, including standard, moisture resistant, vapour, fire and sound boards. Prices are shown ex VAT, and we deliver across England, mainland Wales and mainland Scotland (see delivery information). Call us on 03330 908479, email sales@insulationwarehousedirect.co.uk, or order online.

Sources: Approved Document F, Volume 1 (GOV.UK), Table 1.1; British Gypsum Gyproc WallBoard Duplex product data sheet (limitations of use). Correct at the time of writing.

Back to blog