Is Insulated Plasterboard Worth It? 25mm vs 50mm, Dot and Dab vs Fixing
Quick answer
Insulated plasterboard is worth considering when you want to insulate the inside face of an external wall in one step, and when you cannot afford to lose much floor area. It combines a layer of insulation with a plasterboard face, so it is fitted and finished like a drylining board. Whether the 25mm or 50mm insulant is the better choice depends on the U-value you need to reach. For a solid brick wall, Kingspan's K118 table starts at 52.5mm total board thickness, and the 50mm insulant board (62.5mm overall) gives a U-value of 0.30 W/m²K on timber battens. Always get a condensation risk check.
25mm or 50mm: what the numbers mean
Boards are sold by overall thickness, which includes 12.5mm of plasterboard, while the R-value comes from the insulant alone. Kingspan Kooltherm K118 has a phenolic core with a λ of 0.019 W/mK. In the table below, "25mm" and "50mm" mean the insulant thickness.
| Insulant | Overall board | Insulant R-value (m²K/W) | On 215mm solid brick, battens at 600mm centres |
|---|---|---|---|
| 25mm | 37.5mm | 1.30 | Not listed in Kingspan's table |
| 30mm | 42.5mm | 1.55 | Not listed |
| 40mm | 52.5mm | 2.10 | 0.35 W/m²K |
| 50mm | 62.5mm | 2.60 | 0.30 W/m²K |
| 60mm | 72.5mm | 3.15 | 0.26 W/m²K |
Kingspan notes that some values are omitted from its tables because they do not meet the most common minimum requirements. The target for insulating the inside of an existing wall in England is 0.30 W/m²K under Approved Document L (Table 4.3, renovation of an existing element, 2021 edition with 2023 amendments), so see our guide to the U-values required by Part L. The figures here are guidance only. A full U-value calculation and a condensation risk analysis should be done for each project.
Is it worth it?
- It can save steps. You fix one board rather than building a framework, adding insulation and then a separate plasterboard. Kingspan describes K118 as a drylining board with a tapered edge, so standard drylining finishing applies.
- It is thinner for the same job. Phenolic's low λ means less thickness for a given R-value than PIR (0.022 W/mK on the Kingspan and Recticel datasheets), so you lose less floor space. Our comparison of K118 and Celotex PL4000 covers the PIR alternative.
- It needs careful detailing. The joints, perimeters, reveals and services all need to be sealed and finished properly, and it is not a fix for a damp wall (see below).
- It will not suit every wall. If the existing wall is damp, uneven beyond the adhesive's tolerance or exposed to driving rain, deal with that first.
Dot and dab or mechanical fix?
Kingspan describes both methods for K118. Our step-by-step installation guide and the solid wall fitting guide go into detail.
| Mechanical fix | Adhesive (dot and dab) | |
|---|---|---|
| What it uses | Timber battens or metal studs at maximum 600mm centres, board fixed with drywall screws | Acrylic sealant, PU foam or gypsum-based drywall adhesive, plus secondary fixings |
| Where it suits | Walls where the framework can set the cavity depth to suit the surface | Dry, stable brick, block or concrete walls, or rendered solid walls, free from moisture penetration |
| Watch for | Fixings and battens form part of the U-value calculation | Not suitable directly on non-rendered solid masonry where moisture can penetrate, or on timber or steel frame. Gypsum adhesive needs a bonding agent on the foil facer, with 10 to 25mm dabs and a 15mm wall tolerance |
Vapour and condensation
- K118 has an integral vapour control layer, but the joints and edges must still be detailed so that it works as one.
- Kingspan says two coats of Gyproc Drywall Sealer increase the vapour resistance of the surface, and recommends a condensation risk analysis to BS 5250:2021.
- Do not use it to hide damp. The brochure says it is not suitable for isolating dampness or for continuously damp conditions.
- For wet rooms see our guide to moisture-resistant and vapour plasterboard.
Frequently asked questions
Is 25mm or 50mm insulated plasterboard better?
The 50mm insulant gives double the R-value of 25mm (2.60 compared with 1.30 for K118), and on solid brick it is the thickness Kingspan tables for 0.30 W/m²K. A thinner board suits where room size matters more and a lower U-value is not required.
Can I use insulated plasterboard on a damp wall?
No. Solve the cause of the damp first. Kingspan states that it is not for isolating dampness or for continuously damp conditions.
Do I need a vapour control layer as well?
K118 has an integral VCL. Details at joints and perimeters matter, and a condensation risk analysis is recommended.
Order insulated plasterboard
Browse our insulated plasterboard, including Kingspan K118 37.5mm and K118 62.5mm, and tapes and fillers. We have a £400 ex VAT minimum, with free delivery in England. British Gypsum (including Gypframe), Celotex and Knauf can also go to mainland Wales and mainland Scotland (£400 ex VAT minimum plus £40 + VAT delivery). Access panels can also go to mainland Wales and mainland Scotland, with their own charges (£15 + VAT under £300 ex VAT, free from £300). Other ranges, including suspended ceiling tiles and grid, are delivered in England only. We do not deliver to Northern Ireland or the Scottish islands. Call 03330 908479 for help choosing.
Sources: Kingspan Kooltherm K118 brochure; Approved Document L (GOV.UK); Kingspan guide to types of insulation. Figures are indicative and correct at the time of writing; they are not a substitute for a calculation by your designer or the manufacturer's technical team, and Building Control has the final say.
